Not to worry though; the cleaning process is not as difficult as you may imagine and we are here to help. Let us get right into how to clean a Jack Lalanne power juicer. As we said, the cleaning process is not a complex or difficult one. Here are the steps you need to follow. The first thing you want to do is switch off the appliance by pressing the power button at the back of the appliance.
Wait for the motor to stop running and unplug the power cord from the power output. Do this with dry hands to avoid the risk of electric shock. Next, disassemble the juicer. As you detach each part, put it on a clean surface or on top of paper towels. Disassembling involves detaching the pusher from the chute, pulling the locking bar towards you, removing the pulp guard and lid, and taking out the blade from the unit. Handle the blade with care to avoid being cut.
Never attempt to spray the base with cleaners or submerge it in water. Abrasive cleaners or sponges are likely to damage the finish so avoid them. At this point, you can either toss the disassembled parts in the dishwasher for cleaning or fill your sink with warm water and mix it with mild detergent.
Wash the parts and rinse them under clean running water. Use a towel to dry these parts off or allow them to air dry. Note: If you want to use the dishwasher, check the manual to see if all the parts are dishwasher safe. To clean the blade and filter, you want to rinse them under running water and use a soft-bristled brush to scrub. Rinse again in clean water before drying them with a clean towel. Now that all the parts are clean, you want to dry them manually or allow them to air dry.
After that, you want to reassemble the juicer plug it into a power source and switch it on. This is to spin out any remaining water. You can now store your juicer away for future use. We do not think so. Anyway, there are several tips that can make cleaning your juice easier. This product has been manufactured to the highest standards. Rinse the filter from the outside under running water.
Should you have any problem our lslanne customer service staff is here to help you if you have a question. Place receptacle on the base, with juicer spout facing direction of locking bar. Place lid with pulp guard attached on top Lid with of receptacle, making certain it is snugly Pulp Guard aligned with the pulp guard facing in the opposite direction of the juice spout.
My sister has this juicer however there are no holes in the blade that the crescent tool also non existent would use to remove it. Once turned off it is quite normal for the juicer to spin for a minute or so due to the very fine precision balancing of this appliance.
Remove pusher from the chute. I just need to know how to clean and use it! The juicer would not make the juice. Before disassembling the unit make sure you turn the power OFF and unplug the jaack from the electrical outlet.
If needed, ad these liquid ingredients after the juicing process. We are very proud of the design and quality of our Power Juicer. Page 12 We are very proud of the design and quality of our Janual Juicer.
Place base on a dry flat surface with locking bar in down position as shown. Do not over tighten as the screw peg will break. Warranty Jack LaLanne Power Juicer Limited Lifetime Warranty The manufacturer warrants that your Jack LaLanne Power Juicer is free of defects in materials and workmanship and will, at its option, repair or replace any defective juicer that is returned. Cleaning Your Power Juicer Rinse the filter from the outside under running water.
To clean the blade and filter, hold them under a tap, and rinse them in running water. To remove all pulp from the filter, you have to use a dishwashing brush. After cleaning each component, place it on a clean towel to dry. This one is the most time-consuming step to clean a power juicer. You have to pay a small price to get delicious and fresh juice quickly. When all the components of your juicer become dry, it is time to reassemble them. There is a manual on how to assemble it.
Follow the instructions to make it easy. When you reassemble it, the cleaning process of your Jack Lalanne power juicer is complete. So, keep your juicer in a cool and dry place. In this article, I covered the most simple steps to clean a Jack Lalanne power juicer. According to my practical experience, Jack Lalanne power juicer is a great choice to make juice easily.
It saves time and energy. But some people lose their interest in buying a power juicer for its mega cleaning process.
But I think after reading this article, you have got a basic concept about how to clean this and that will inspire you to use it. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment.
A power juicer contains the following components: Round cylindrical pusher Pulp collector The filter Lid with a built-in pulp guard Crescent tool Blades The receptacle with its juice spout And, the base. Taking The Components Apart In this step, disassemble your power juicer correctly because Jack Lalanne juicer requires its own way to dismantle it. Remove the food pusher from the top. Use one hand to hold the base and another to remove that.
Now carefully, remove the lid with its built-in pulp guard. Pull it up vertically to remove it from the base. Then you have to remove the pulp collector.
0コメント